- Products & Solutions
- All Industries
- About Us
By Richard Juskowiak, Donaldson Process Filtration
Reverse osmosis (RO) filtration systems purify water used in the processing of food and beverages, pharmaceuticals, and other consumable products. Because RO membranes are key to product safety and also costly to replace, it’s important to protect them from the buildup of biofilm. Biofilm occurs when bacteria survive the activated carbon dichlorination step and multiply downstream to form microbe colonies on equipment surfaces.
The better source water is pre-filtered, the better it prevents biofilm formation on the RO system, improving both product safety and RO membrane life. The FDA requires a pre-filter on water before it enters RO systems, but attention to the type of pre-filter used has many benefits.
An RO membrane that is well protected from microbes and damaging carbon particles typically lasts up to two years, while one that fouls within a year may be an indication of substandard pre-filtration.
Here are three ways to better protect the RO membrane with higher performing pre-filtration:
Industry standards recommend a 5-micron filter for RO pre-filtration, but not all 5-micron filters are alike. For many years, the only choice for processors has been the melt-blown filter—a polypropylene cylinder injected with nonwoven polymer. The random nature of this manufacturing process allows for open spaces and inconsistent microbe capture.
Improved filtration technology is now available, thanks to a collaboration among materials scientists, engineers, and beverage processors. Under the name LifeTec™ from Donaldson, the advanced media structure and housing in these filters delivers greater capacity and reliability.
LifeTec media is folded in pleats inside a polypropylene cage, which, compared to melt blown elements, expands filtration surface area by 400% to capture more contaminants without impeding process flow rates.
The dense media is engineered with larger pores on the upstream side narrowing to smaller ones on the downstream surface. This funnel structure creates a specific micron cut-off range and therefore delivers greater confidence that a pre-filter is effective.
When selecting a filter, look beyond the micron size on the supplier’s technical data sheet, and seek out the “efficiency” rating. Efficiency is the percent of particulates a filter is verified to capture in the micron range on the label. Because there are no widely accepted measurement standard governing filter manufacturers, discernment in this area is important. Micron ratings, along with the terms “nominal” and “absolute,” are quite subjective, similar to claims of “low fat” in food labeling.
To illustrate how this confusion can happen, Donaldson tested melt-blown filters from five different manufacturers, all claiming to remove 1-micron contaminants. Because of the random fiber composition of the melt-blown filters, their efficiency performances ranged from below 20% to above 98%.
Newer filtration technology can be much more precise. The efficiency of LifeTec filters, for example, can be verified with laboratory testing, which Donaldson provides on all its process filters.
A LifeTec absolute rated filter with a capture size of 1 micron, for instance, will always remove 99.98% of particles 1 micron or larger. Donaldson periodically re-tests its filters to confirm this performance, and openly publishes this rating on all its labeling and data sheets.
Finally, when making a serious attempt to prevent biofilm build-up at the lowest cost, think beyond the purchase price of the pre-filter. Many plants routinely schedule replacement of their melt-blown RO pre-filters once a week, out of habit. These costs add up.
While advanced pleated filters may cost more initially, the potential long-term cost savings can considerable:
For optimal RO membrane protection, filtration engineers at Donaldson recommend installing a 1-micron absolute rated pleated filter either in place of the melt-blown filter, or directly after it, before water contacts the RO membrane. Doing so will not only extend the life of the RO membrane, but the pre-filter itself will last longer and maintain higher-volume flow rates due to the pleated design as well.
It is also important for operators to source their filters from a manufacturer that conducts and freely publishes its retention efficiency data with the corresponding micron size.
Please complete the form below to continue reading "Reducing Costly Biofilm Build-up in Reverse Osmosis Membranes".